Aluminum Wet Glaze Base Shoe

To add to cart, choose from the options below.

Base support for railing installation

Suitable for mortar insertion installations
Type of Mounting: Face Mount Floor Mount Safety Glass Thickness: 10 to 12 mm Base section hole drilling patterns: Counter Bore Side Drilled Height: 4 1/8 in Width: 2 1/2 in 2 3/4 in Length: 10 ft 12 ft 20 ft Packaging format: Length of 10 linear foot Length of 12 linear foot Length of 20 linear foot Select Options
Product # Type of Mounting Safety Glass Thickness Base section hole drilling patterns Height Width Length Packaging format
HRTV0099101210 Face Mount 10 to 12 mm Side Drilled 4 1/8 in 2 1/2 in 10 ft Length of 10 linear foot
HRTV0099101212 Face Mount 10 to 12 mm Side Drilled 4 1/8 in 2 1/2 in 12 ft Length of 12 linear foot
HRTV0099101220 Face Mount 10 to 12 mm Side Drilled 4 1/8 in 2 1/2 in 20 ft Length of 20 linear foot
HRTV0090101210 Floor Mount 10 to 12 mm Counter Bore 4 1/8 in 2 1/2 in 10 ft Length of 10 linear foot
HRTV0090101212 Floor Mount 10 to 12 mm Counter Bore 4 1/8 in 2 1/2 in 12 ft Length of 12 linear foot
HRTV0090101220 Floor Mount 10 to 12 mm Counter Bore 4 1/8 in 2 1/2 in 20 ft Length of 20 linear foot
HRTV0090191910 Floor Mount 19 mm Counter Bore 4 1/4 in 2 3/4 in 10 ft Length of 10 linear foot

REQUIRED PRODUCTS

Requires ONE of the following products
OR
OR

TECHNICAL SPECIFICATIONS

Recommended Location Usage
Interior, Exterior
Thickness
3/4 in
Finish
Mill Finish
Material
Aluminum 6005-T5
Glass Drilling
Not Required
Category
Base Shoes
Milling Diameter
9/16 to 7/8 in
Milling C/C
12 in

APPLICATION

-Typically used as the base channel for installation of glass railing systems and windscreens.
-Usual maximum dimension of glass panel is 42'' tall by 4-5 ft. wide. Before installation, engineer approval is required to ensure compliance with building codes.

IMPORTANT INFORMATION

The glass must be shaped according to the section plane provided in the box.
Always set the product in a suitable material.
Never exceed the load or maximum size recommended by the manufacturer.
Never use a spray lubricant on this product.
Maintenance: clean with a soft cloth and non-abrasive soap or ammonia.
This illustration is provided for visual reference only. Actual product may differ from the illustration. Order hardware before starting the job. The manufacturer reserves the right to change product and information without notice. Always use the instructions inside the package.

Drawings and technical documents contain examples of hardware from different manufacturers. The customer may in no case make a claim following the use of these documents. The Company disclaims any responsibility for the structural details related to a construction or project. Installation must be done by qualified personnel. Always make sure that the product is properly installed using suitable fixings to the support material. Never exceed the load or maximum size recommended by the manufacturer. Never use a spray lubricant on this product.

DISCLAIMER

The preceding information as well as any technical recommendation given in writing, verbally or based on tests is provided to the best of our knowledge. However, recommendations are non-binding and do not diminish your responsibility for determining the correctness of these recommendations and the suitability of the product for your particular purpose. The application, use or processing of our products as well as the production of products based on our technical recommendations are beyond our control and therefore exclusively your responsibility. Sales of our products are subject to our most recent General Sales and Delivery Conditions. Please note that Richelieu will not accept any returns or claims for unpackaged products.