Technical data sheet
UltraSeal PF-10 Foam Cleaner
Product # 947340011
UltraSeal® PF-10 Foam Cleaner is a cleaning solvent used to dissolve any uncured foam or adhesive foam from unwanted places.
Uniquely designed for use with Nuco dispensing guns.
UltraSeal® PF-10 also works for general cleaning purposes, but is mainly used to clean excess uncured polyurethane foam and foam applicators.
Uniquely designed for use with Nuco dispensing guns.
UltraSeal® PF-10 also works for general cleaning purposes, but is mainly used to clean excess uncured polyurethane foam and foam applicators.
ADVANTAGES AND BENEFITS
UltraSeal® PF-10 Foam Cleaner is designed to flush out any remaining uncured foam or adhesive from your gun, leaving it in good working condition and ready for your next project. Typical consumption is one can of cleaner per case of foam or adhesive. Please note that Ultra Clean will not dissolve cured foam or adhesive.
- Instantly cleans up uncured foam
- Helps maintain foam gun performance
- Essential for gun maintenance
- Attaches to foam gun, or can be used with a spray nozzle
- Can be used over and over again!
- Instantly cleans up uncured foam
- Helps maintain foam gun performance
- Essential for gun maintenance
- Attaches to foam gun, or can be used with a spray nozzle
- Can be used over and over again!
TECHNICAL SPECIFICATIONS
Product #
947340011
Packaging Specifications
Pressurized Cartridge
Format
12 oz
Brand
Nuco
APPLICATION
Be prepared. Wear protective goggles, gloves, and clothing.
Clean in a well-ventilated area with a plastic-lined trash barrel.
Shake can well before spraying or attaching can to Nuco dispensing gun.
DO NOT use in a horizontal position.
For general cleaning, attach plastic nozzle to valve of can.
For gun cleaning, screw Ultra Clean can onto gun basket (finger-tighten only).
Carefully pull trigger to discharge cleaner through gun.
Spray until all traces of foam or adhesive have been removed and you see that all yellowish resin has been cleaned from gun.
Release gun trigger and let solvent soak in gun for 1 to 3 minutes.
Remove PF-10 can from the Nuco dispensing gun and place a new can of UltraSeal® gun foam onto the dispensing gun.
Spray new foam can into the plastic-lined trash barrel for 10 seconds to purge out all remaining cleaner still in the dispensing gun.
Clean in a well-ventilated area with a plastic-lined trash barrel.
Shake can well before spraying or attaching can to Nuco dispensing gun.
DO NOT use in a horizontal position.
For general cleaning, attach plastic nozzle to valve of can.
For gun cleaning, screw Ultra Clean can onto gun basket (finger-tighten only).
Carefully pull trigger to discharge cleaner through gun.
Spray until all traces of foam or adhesive have been removed and you see that all yellowish resin has been cleaned from gun.
Release gun trigger and let solvent soak in gun for 1 to 3 minutes.
Remove PF-10 can from the Nuco dispensing gun and place a new can of UltraSeal® gun foam onto the dispensing gun.
Spray new foam can into the plastic-lined trash barrel for 10 seconds to purge out all remaining cleaner still in the dispensing gun.
IMPORTANT INFORMATION
UltraSeal® PF-10 is an aerosol material and must be kept below 49 °C (120 °F).
DISCLAIMER
The preceding information as well as any technical recommendations given in writing, verbally or based on tests are provided to the best of our knowledge. However, they are non-binding recommendations only and do not affect your responsibility to determine the correctness of given recommendations and suitability of the product for your particular purposes. The application, use or processing of our products as well as the production of products based on our technical recommendations are beyond our control and therefore fall exclusively in your area of responsibility. Sales of our products are effected according to our most recent General Sales and Delivery Conditions.